Click for printable PDF

This is a howto from Elektra on building an antenna reflector for your Mesh Potato. Properly attached and deployed it should more or less double the existing range of the MP.

Basic Material

190 x 240mm blank aluminium sheet, 1.5mm thick.

You can use wider than 190mm, if the store sells 200mm wide this is also fine. I recommend to have a professional workshop cut the metal sheet to the outer dimensions. The store where you buy it might do this. They have the tools to easily cut it to a straight form. I did it by hand, it doesn’t look perfectly straight. Doesn’t matter for the function, though.

Tools required

• drill (a drill press preferably, as a hand-held drill tends to slide over the metal, so holes might end up not positioned accurately)
• 5.1mm drill for metal (That is the diameter required for the 5mm rivets)
• white paint
• alcohol as solvent to remove grease from the surface and some old cloth
• cable ties
• some means to cut metal sheet (metal shears might do, but working with 1.5mm aluminium sheet is quite hard)
• four 5x10mm rivets
• rivet gun
• centre punch
• hammer
• a small file
• 4 mm drill
• 2 pieces of flat metal to construct the support brackets
• box cutter / stanley knife
• double sided tape (goes between the MP and the reflector)
• optional: coping saw with metal saw blade (makes it easier to work out the 4x10mm holes)
• hose clips (instead of cable ties for the pole mount)

Steps

1. Print the plan on A4 paper and have a copy shop print it on to transparent foil.
2. Use the box cutter to cut the outer shape out of the foil.
3. Fix the foil on the metal sheet. Mark the lines to cut.
4. With the box cutter, cut the 4x10mm holes (for the cable ties) through the foil and into the metal.
5. With the centre punch and the hammer mark the location of the holes.
6. Drill holes and cut where indicated.
7. Work out the 4x10mm holes.
8. Round the outer corners with the file.
9. Removed the cutting ridges with the file.
10. Remove grease from aluminum plate.
11. Spray paint the reflector, leaving plenty of time for the paint to dry.
12. Fix the rear mounting support brackets with the rivets.
13. Apply the double sided tape between the MP and the reflector.
14. Carefully attach the MP to it. Make sure the LEDs match with the holes.

Finished MP with Antenna Reflector

We want to use etched PCB Wifi antennas for the Mesh Potato. However we have heard that some companies have had problems with PCB antennas, such as variable results in production. So before committing to PCB antenna we wanted to do some more tests.

Joel is a local hacker here in Adelaide who happens to live at the top of a 4 story apartment block in a beach side suburb called Henley Beach. This gives him good line of sight to points on the ground several hundred meters away. Much easier than testing at my place which is on dead flat terrain and requires masts for any Wifi range testing.

Before heading out to Joel’s place I tried some tests in my backyard. I set up two MP01s about 10m apart. First I connected conventional sleeve dipole (rubber ducky) antennas and measured the signal strength. I then connected a couple of PCB antennas and repeated. To monitor signal levels I wrote a simple script to dump the Received Signal Strength Indication (RSSI) levels (in dBm) from MadWifi:

#!/bin/sh

while [ 1 ]
do
wlanconfig ath0 list | grep 56:ac:90 | awk ‘{ print $6 }’
sleep 1
done

The grep filters out the last few MAC digits of the MP we are interested in, otherwise you get RSSI measurements of all nearby Wifi devices.

However the results were inconclusive and after an hour I became frustrated:

• On a good test both MPs would receive about -30dBm, however if I moved a MP 20mm a level could drop to -44dBm. Lots of multipath in my back yard!
• One MP was consistently around -30dBm, whereas the other would move between -30 and -48dBm. Maybe they had different diversity antenna settings. Or maybe the RSSI measurements can’t be trusted.

I had much better (and less frustrating) results using the spectrum analyser to measure signal strengths, as explained in the previous post on PCB Wifi antennas.

In the end I figured it was sufficient to test from a system level rather than attempt more measurements of antenna performance and signal strength. The $64 dollar question is can we make phone calls over a reasonable distance with these antennas?

On the Beach

We placed one MP01 on Joel’s balcony. I then walked down to the end of Henley Jetty (Joel has previously managed to pick up his home Wifi there). There is (just) a line of site between the two points – through a gap in a couple of buildings. The distance was 375m. We used two calibrated V1.2 MP01s (same design as the Beta units). An “iwlist ath0 scan” showed 9 other Wifi networks in operation.

Google Map of Range Test - 375m

One MP01 on Joel's Balcony

I tried a bunch of antenna combinations, starting with regular sleeve dipole (rubber ducky) antennas then moving to PCB antennas first at one end, then both ends of the link. From our previous tests both the sleeve dipole and the PCB monopole antennas have an estimated gain of 2dBi.

We had a total of 4 PCB antenna samples (a mixture of the 17mm and 20mm monopoles) as we wanted to get a feel for performance spread over multiple antennas of the same design. Here are the results:

The final test was just to make sure we weren’t kidding ourselves.

MP01 on the end of Henley Jetty

At one stage a fisherman assisted in my propagation experiments by standing right in my line of site and lowering a metal net as I talked to Joel!

For each call I tried moving the MP01 (with PCB antenna attached) around. For example upside down, side to side, rotated it. No break up of signal, good audio in both directions. Only problem was wind noise. Joel suggested we add digital noise suppression but I figure there isn’t much wind noise inside village homes!

Here is the view of the far end from either side of the link. The arrow shows the location of the other end.

View of Jetty from Joel's Balcony

View of Joel's Balcony from Jetty That's him with the brown eyes.

Jeff designed three types of antennas which I laid out on PCB and had fabricated locally. The three designs were a dipole, a monopole, and a biquad (single loop). We made three versions of each PCB antenna with slightly different dimensions.

I also made a some wire antennas, a monopole, a biquad (dual loop), and a quad (single loop).

Our PCB and wire antennas

PCB biquad design

PCB Monopole Design

Checking the Antenna Impedance

When the PCBs came back the first step was to check the impedance of each antenna. We want roughly 50 ohms impedance to ensure the maximum amount of power is transferred from the Mesh Potato transmitter to the antenna.

A Standing Wave Ratio (SWR) bridge can be used to measure the SWR. I used a version of the design by Erwin Gijzen, a radio Ham and Wifi experimenter. I constructed the SWR head, and measured the DC voltage from the bridge using a multimeter. The bridge compares the impedance of the antennas to a known 50 ohms impedance. If they are equal then the DC output from the bridge should be 0V. Various degrees of mis-match give different output voltages.

SWR head, microwave PCB made with a Dremel tool

I constructed the bridge from double sided PCB and cut the microstrip (3mm wide on 1.6mm thick FR4) with a Dremel tool to save time. When tested it gave sensible results once I fitted a decent microwave detector diode. Unlike Erwin I couldn’t null it down to 0V with a reference 50 ohm load but it did give indicative readings that enabled me to compare our antennas to reference antennas and determine if they had a reasonable match to 50 ohms.

Here are some results:

The 17mm and 20mm monopoles look good, close to the reference 50 ohm load and commercial off the shelf router antennas (which have sleeve dipole construction internally). The wire antennas also look good. The PCB dipole and PCB biquads don’t look so great.

I tuned the wire monopole to a low SWR by snipping off bits of wire, 0.5mm at a time. I started with a length of 31mm (free space quarter wavelength at 2.4 GHz) but found a good SWR at 26mm. This is probably due to the dielectric constant of the insulation on the wire affecting the wavelength.

Antenna Test Range

I constructed a test range in my back yard, along the lines discussed by Erwin. I used a Nanostation 2 at the transmitter, sending continuous 802.11b broadcast pings as described here. The antenna under test was placed about 6m away and a spectrum analyser used as the receiver. It wasn’t a very good antenna range but after some experimentation we did get surprisingly repeatable results when we compared our antennas to several control antennas.

I fashioned a clamp on a tripod to hold the antennas:

Tripod and clamp

However the tripod and clamp didn’t work very well. When I swapped antennas the results differed wildly in exactly the same position. It’s hard to place a 17mm printed monopole in the same position as a 80cm colinear antenna as their sizes are so different.

So instead I moved each antenna around by hand until I found the peak amplitude, which was captured by the “max hold” function of the spectrum analyser. Sounds a bit rough but gave good repeatable results, and Jeff and I achieved similar results when testing.

Path Loss

The 802.11b signal peaked at about -30dBm on the spec an. Using the Wifi power measurement method described here this means a total received power of -20dBm.

The expected received signal is:

Pr = Tx power + Tx antenna gain – path loss + Rx antenna gain – coax loss

So we plug in the numbers from the Nanostation 2, a 6m path loss and the 8dBi gain Superpass omni reference antenna we get:

Pr = 16 + 12 – 56 + 8 -1 = -19dBm

which is pretty close to what we are measuring using the spectrum analyser. If only all my calculations came out this close!

Antenna Gain Results

We used the 8dBi Superpass as a reference. We would first measure the signals from the Superpass, then save that on the screen as signal A. We would then measure the test antennas and calculate the antenna gain based on the known Superpass gain. We moved each antenna around by hand until a peak was found (the max hold function made this straight forward).

We repeated these tests several times over the day, and while the absolute levels would change 1-2dB the relative levels were always similar.

The antennas are listed in order of gain, and I would estimate the measurements have a tolerance of +/- 1dB. The RF level is the peak of the 802.11b signal on the spectrum analyser.

Discussion

The location of the physical position where peak received signal was found was quite “sharp”. This may have been due to lobes in the signal from the Nanostation 2 or multipath.

Several commercial router antennas were tested (sleeve dipole construction), they all measured about the same. The internal design of these antennas is discussed here.

The results from the control antennas (15dB grid, 8dB Superpass, and nominal 2dB sleeve dipole commercial router antennas) are consistent with what we would expect, which gives us some confidence in the other test results.

The impedance match and gain results from the PCB biquad are poor, which suggests the antenna is not resonant at 2.4GHz. It would be nice to test this antenna on a network analyser to find out where they are resonant (please contact me if you have one – I will ship an antenna to you!) Jeff is working up a simulation of the PCB biquad to test the design. We aren’t pursuing the PCB dipole as we have a bunch of antenna candidates that perform just as well (2dBi).

The wire biquad performance with a reflector was remarkable, nearly as good as the grid antenna which is a much larger antenna. The measured gain (12dBi) is consistent with other peoples results for this antenna.

Jeff and I really liked the wire antennas due to their performance and simplicity. They are easy to make: in production they could be bent up on a jig on 10 seconds from stiff copper wire then soldered to the Mesh Potato motherboard. One small problem with the dual loop biquad wire antennas is a feed arrangement – a small piece of coax would be needed to reach the central feed point. We don’t want the antenna wire directly over the PCB, as this would affect performance. The single loop wire quad is simpler in this regard, as it could be attached at one corner to the PCB.

The PCB monopoles perform well and are very simple, just a 17mm x 3mm track on the PCB next to a good chunk of ground plane. Virtually zero cost to add to the Mesh Potato motherboard. Both the 17mm and 20mm versions worked well, which suggests a relatively wide bandwidth and a high tolerance to small variations in manufacture like dieletric constant of the PCB substrate. Antennas fabricated on PCB are physically smaller than their wire cousins as the signals travel slower which means a smaller wavelength for a given frequency.

Wire single and dual loop biquad/quad antennas had above average gain and some directivity, with both peaks and nulls evident as they were rotated. Is directivity a good thing for a mesh router? You might enhance the signal of one node but null out the signal from another. I am not sure.

The higher gains of some antennas look attractive but may not be useful in practical mesh networks. To achieve the highest gain required careful adjustment of the antenna position. This is fine in a traditional point-point Wifi link, but in a mesh network their are multiple nodes we want to talk to. So if you peak the response to one node, you may dip the response to another. I guess it depends on how many nodes you want to talk to.

The reflector was a piece of blank PCB about 20cm x 20cm. It was moved back and forth behind the antenna until a peak was found (usually at around 15-20mm). All antennas improved by at least 4dB with the reflector, the wire biquad improved by 6-8dB. David C has suggested a slide-in reflector arrangement to give a choice between omni and directional antennas. These tests confirm David’s suggestion is a good one, if a precise way to mounting the reflector can be found.

Here are some of the antennas tested grouped by gain.

Antennas grouped by gain, highest gain on the left